MPS-700
The advanced pilling system is equipped with the most important features and impresses with its ease of use on the construction site.
MPS Lite
The basic system for indicating piling mast level primarily based on CAN communication.
MPPS 700
Moba Piling & Pressure Monitoring system is used for Vibro Driving Equipments to monitor, record and report various parameters. Vibro/Piling equipments facilitate penetration of profiles, tubes, sheet piles, etc into the grounds.
CHALLENGES regarding piling on construction site
Machine alignment
Aligning the machine is an additional difficulty in the slope alignment of the drilling arm.
PARALLEL DRILL HOLES
It’s difficult to drill parallel holes, only with marks on the ground.
Exact depth
It’s nearly impossible to drill all holes to the same depth without any measuring system.
High operation costs
The manual measuring causes high operating expenses and is also a huge time factor.
Safety
If the boreholes are drilled in the wrong position, explosions may result in rockfall and a dirty break-off edge.
Drill alignment
It’s difficult to drill all the holes in the same angle.
Solutions
01
Advanced Piling system with easy to use user interface
MPS-700
MOBA's advanced MPS-700 piling system enables you to prepare your drill with precisely measured, uniform drill holes and effectively boost your cost efficiency on the construction site. Save time by eliminating time-consuming physical measurement and drilling parallel holes of the same depth measurement and mast angle in a few simple steps with the help of the system. Because to the exceptional adaptability, you can also benefit from cost and time-efficient upgrades from a wide range of various components.
MPS-700 System components
V700 DISPLAY
V700 is a freely programmable display computer with 7” high brightness full-colour WVGA TFT with PCAP touch screen. The strong LED backlight in combination with the optically bonded PCAP, results in excellent sunlight readability.
ECAN MODULE
Specific solution for interfacing with various sensor and machine equipments via software-configurable input settings.
ENCODER
Precise measurement of the drill depth with the rotary encoder. It has a measuring range of 360° and a PWM/analog interface.
MPC-113 CONTROLLER
MSC 113 is a Machine Signal Computer. It is essential for reading and processing engine and hydraulic data.
SLOPE SENSOR
2-axis tilt sensor with a measuring range of ±60°. The zero point adjustment is done via an infrared interface.
4G CAN GATEWAY
It provides machine location and performance data on the IOT platform using CAN communication with GPS and 4G connectivity.
02
MOBA PILING system for precise PILING ANGLE INDICATOR
MPS Lite
With MOBA's MPS-Lite piling system, you can precisely measure your piling angle using the slope sensor and the smartview display in a few simple steps.
MPS Lite Components
SMARTVIEW DISPLAY
It is intuitive and simple to use, providing all essential information such as piling angle, tilt indicator, and calibration.
SLOPE SENSOR
2-axis tilt sensor with a measuring range of ±60°. The zero point adjustment is done via an infrared interface.
03
Advanced Piling system with easy to use user interface
MPPS-700
MOBA's advanced MPPS-700 Piling and Pressure monitoring system, used on Vibro Equipments especially for the Foundation jobs like Diaphragm walls and coastal/soft soil stabilisation. MPPS 700 equipped with advanced sensors and display computer measures, monitors, records various important parameters like Depth, Inclination, Hydraulic Pressure, Penetration rate of soil. On top of monitoring and recording, using our desktop software a customised report can be generated for further reporting to authorities.
Compnents of MPPS 700 are designed specially to operate in harsh environemnts of construction sites.
MPPS-700 SYSTEM COMPONENTS
V700 DISPLAY
V700 is a freely programmable display computer with 7” high brightness full-colour WVGA TFT with PCAP touch screen. The strong LED backlight in combination with the optically bonded PCAP, results in excellent sunlight readability.
ENCODER
Precise measurement of the drill depth with the rotary encoder. It has a measuring range of 360° and a PWM/analog interface.
SLOPE SENSOR
2-axis tilt sensor with a measuring range of ±60°. The zero point adjustment is done via an infrared interface.
4G CAN GATEWAY
It provides machine location and performance data on the IOT platform using CAN communication with GPS and 4G connectivity.
